devc-ser8250-ixp2400, devc-tser8250-ixp2400

8250 serial communications manager (QNX Neutrino)

You must be root to start this driver.

Syntax:

devc-ser8250-ixp2400 [[options] 
              [port[^shift][,intr]]]... &

devc-tser8250-ixp2400 [[options] 
               [port[^shift][,intr]]]... &

Runs on:

x86, PowerPC, and MIPS hardware with an 8250-compatible UART

Options:

The options are position-dependent and affect the subsequent ports.

-b number

The initial baud rate (default 57600).

-C size

The size of the canonical buffer in bytes (default 256).

-c clock[/divisor]

Define a custom clock rate, in hertz, and divisor for the serial port. The default (-c 1843200/16) is suitable for compatible PC serial ports.

-E

Start in raw mode (the default). Software flow control is disabled by default.

-e

Start in edited mode (default raw). Software flow control is enabled by default.

-F

Disable hardware flow control (default to hardware flow control enabled). Hardware flow control is not supported in edited mode.

-f

Enable hardware flow control (default). Hardware flow control is not supported in edited mode.

-I number

The size of the interrupt input buffer in bytes (default 2048).

-O number

The size of the interrupt output buffer in bytes (default 2048).

-S|s

Disable / enable software flow control. The default depends on the mode: in raw mode (-E, the default), it's disabled; in edited mode (-e), it's enabled.

The order in which you specify the -E or -e, and -S or -s options matters:

Options	Mode	Software flow control
-e	Edited	Enabled
-S -e	Edited	Enabled
-e -S	Edited	Disabled
-E	Raw	Disabled
-s -E	Raw	Disabled
-E -s	Raw	Enabled

-T number

Enable the transmit FIFO and set the number of characters to be transmitted at each TX interrupt to 1, 4, 8, or 14. The default is 0 (FIFO disabled).

-t number

Enable the receive FIFO and set its threshold to 1, 4, 8, or 14 characters. The default is 0 (trigger disabled).

-u number

Append number to the device name prefix (/dev/ser). The default is 1; additional devices are given increasing numbers.

port

The hex I/O address (for x86 systems) or the physical memory address (for PowerPC and MIPS) of a serial port.

shift

The spacing of the device registers as a power of 2. For example:

0

Registers are 1 byte apart.

1

Registers are 2 bytes apart.

2

Registers are 4 bytes apart.

...

n

Registers are 2ⁿ bytes apart.

The default shift is 0.

intr

The interrupt used by this port; specified in hex if prefixed with 0x, otherwise it's decimal.

Description:

The devc-ser8250-ixp2400 manager is a small serial device manager for QNX Neutrino. It can support any number of serial ports using 8250s, 14450s or 16550s. Each device can be assigned its own interrupt, or share an interrupt if the hardware supports interrupt sharing. If you don't specify any I/O ports for devices on an x86 system, devc-ser8250-ixp2400 assumes you want to use the standard PC ports of COM1 (3f8,4) and COM2 (2f8,3).

The devc-tser8250-ixp2400 manager is a "tiny" version of devc-ser8250-ixp2400 that's intended for memory-constrained systems. It doesn't support special character editing (e.g. toggling insert mode, special erase characters).

Each device is given a name in the pathname space of /dev/sern, where n starts at 1 (unless changed via the -u option) and increases. If you use the default PC serial ports, this results in:

If your application uses /dev/console, you should create a link from it to one of /dev/ser1, /dev/ser2, ... by adding a line like this to the buildfile used by mkifs: [type=link] /dev/console = /dev/ser1

All devices are fully interrupt driven and by default support standard hardware flow control on input and output (RTS/CTS). This can be disabled by the -F option.

Hardware flow control is not supported in edited mode.

A read request by default returns when at least 1 character is available. To increase efficiency, you can control three parameters to control when a read is satisfied:

Time

Return after a specified amount of time has elapsed.

Min

Return when this number of characters are in the input buffer.

Char

Return if this forwarding character is in the input buffer.

If the Min value is greater than the size of the input buffer, the Min value is clipped to the size of the buffer. To avoid this, the size of the input buffer can be changed with the -I option.

These parameters are set using library routines (see tcgetattr(), tcsetattr(), readcond() and TimerTimeout() in the Library Reference).

The devc-ser8250-ixp2400 manager supports both raw and edited modes, making it a real tty device.

The following fields and flags are supported in the termios structure:

Examples:

Start devc-ser8250-ixp2400, defaulting for COM1 and COM2:

devc-ser8250-ixp2400 &

Start devc-ser8250-ixp2400, defaulting for COM1 and COM2, but change baud rate to 38400 from 57600 default:

devc-ser8250-ixp2400 -b 38400 &

Start devc-ser8250-ixp2400 with five ports (the last four preset to 38400 baud):

devc-ser8250-ixp2400 3f8,4 -b 38400 280,3 288,3 290,3 298,3 &

You can specify multiple -F and -f options; they're position-dependent, and affect the next serial port:

devc-ser8250-ixp2400 -F 3f8,4 -f 2f8,3 &

Start devc-ser8250-ixp2400 on an NEC 4111 eval board (MIPS):

devc-ser8250-ixp2400 0x1600ffc0^1,0x80010007 &

See also:

Character I/O drivers (devc-*) in the Utilities Summary