View topic - Network Problem

Network Problem

Discussions, suggestions, requests about this website.

Network Problem

Postby uday » Tue Aug 05, 2003 11:16 am

I have installed QNX 6.2.1 on my IBM netvista Pc. It is not recognising my network connection. I am working on ethernet network. I tried with io-net speedo. It is not working. Becuase of this i am not able to setup internet connection. Can anyone help me out!!!.
Please give me step by step procedure to do this.

details of pci -v related to ethernet is as follows

Class = Network (Ethernet)
Vendor ID = 8086h, Intel Corporation
Device ID = 1039h, Unknown Unknown
PCI index = 0h
Class Codes = 020000h
Revision ID = 81h
Bus number = 1
Device number = 8
Function num = 0
Status Reg = 290h
Command Reg = 117h
Header type = 0h Single-function
BIST = 0h Build-in-self-test not supported
Latency Timer = 42h
Cache Line Size= 8h un-cacheable
PCI Mem Address = c0100000h 32bit length 4096 enabled
PCI IO Address = 2000h length 64 enabled
Subsystem Vendor ID = 1014h
Subsystem ID = 267h
Max Lat = 56ns
Min Gnt = 8ns
PCI Int Pin = INT A
Interrupt line = 11
Capabilities Pointer = dch
Capability ID = 1h
Capabilities = fe22h - 3a004100h
uday
Active Member
 
Posts: 10
Joined: Tue Aug 05, 2003 10:58 am

Postby cdm » Tue Aug 05, 2003 7:09 pm

Try explicity giving the device id for the device.

slay -f io-net
io-net -d speedo did=0x1039,vid=0x8086,verbose -p tcpip
cdm
QNX Master
 
Posts: 789
Joined: Fri Jul 05, 2002 9:38 am

Postby uday » Wed Aug 06, 2003 7:02 am

I tried it. but it did not work. I got error message as follows :
"unable to init dll devn-speedo : No such deveice"

I also tried io-net -d eepro -p tcpip . But did not work.

I tried io-net -d ne2000 did=0x1039,vid=0x8086,verbose -p tcpip. This is working. Device is getting activated but device tab is not reflected in network panel. why?
uday
Active Member
 
Posts: 10
Joined: Tue Aug 05, 2003 10:58 am

Postby uday » Wed Aug 06, 2003 7:03 am

I tried it. but it did not work. I got error message as follows :
"unable to init dll devn-speedo : No such deveice"

I also tried io-net -d eepro -p tcpip . But did not work.

I tried io-net -d ne2000 did=0x1039,vid=0x8086,verbose -p tcpip. This is working. Device is getting activated but device tab is not reflected in network panel. why?
uday
Active Member
 
Posts: 10
Joined: Tue Aug 05, 2003 10:58 am

Postby xtang » Wed Aug 06, 2003 3:55 pm

Make sure there is no space between commas. The whole
"did=0x1039,vid=0x8086,verbose" should be no space in it.

Loading other drivers won't help you. Some drivers like ne2000
won't be able to confirm the hardware so it blindly accept what
ever you put on command line, and of cause it won't work for you.
xtang
QNX Master
 
Posts: 313
Joined: Thu Jul 18, 2002 5:01 pm

Postby uday » Thu Aug 07, 2003 10:45 am

Thanks a lot. It is working.
uday
Active Member
 
Posts: 10
Joined: Tue Aug 05, 2003 10:58 am


Return to OpenQNX Site

Who is online

Users browsing this forum: No registered users and 1 guest