QNX 6.2.1 NC ethernet card problem

bridged with qdn.public.installation
Post Reply
xinni

QNX 6.2.1 NC ethernet card problem

Post by xinni » Tue Jul 29, 2003 4:22 am

I installed 6.2.1NC, but I cannot have the ethernet card running: when I
configure the en0 to use DHCP, I got an pop-up message "netmanager
error:could not configure DHCP on interface en0. netmanager error: couldnot
reach DHCP server on interface en0."

I have a Macronix PCI ethernet adatper, and I am using driver "io-net -d
tulip -p tcpip".

Can anyone help me please?

Frédéric Paquet-Roy

Re: QNX 6.2.1 NC ethernet card problem

Post by Frédéric Paquet-Roy » Thu Jul 31, 2003 5:51 pm

I have the same problem with a ne2000 compatible board. It is a CM202 from
Real Time Devices.
I am suspecting a defective board. Maybe it is the same for you.

If someone has a better idea...


"xinni" <xiahnisong2001@rogers.com> wrote in message
news:bg4s84$47j$1@inn.qnx.com...
I installed 6.2.1NC, but I cannot have the ethernet card running: when I
configure the en0 to use DHCP, I got an pop-up message "netmanager
error:could not configure DHCP on interface en0. netmanager error:
couldnot
reach DHCP server on interface en0."

I have a Macronix PCI ethernet adatper, and I am using driver "io-net -d
tulip -p tcpip".

Can anyone help me please?


xinni

Re: QNX 6.2.1 NC ethernet card problem

Post by xinni » Fri Aug 01, 2003 3:32 am

My network card works fine with windows XP and Linux 8.0. so I don't think
it's an issue.
Is this a known bug with 6.2.1?


"Frédéric Paquet-Roy" <frederic.paquet-roy.1@ens.etsmtl.ca> wrote in message
news:bgbkcc$94h$1@inn.qnx.com...
I have the same problem with a ne2000 compatible board. It is a CM202
from
Real Time Devices.
I am suspecting a defective board. Maybe it is the same for you.

If someone has a better idea...


"xinni" <xiahnisong2001@rogers.com> wrote in message
news:bg4s84$47j$1@inn.qnx.com...
I installed 6.2.1NC, but I cannot have the ethernet card running: when I
configure the en0 to use DHCP, I got an pop-up message "netmanager
error:could not configure DHCP on interface en0. netmanager error:
couldnot
reach DHCP server on interface en0."

I have a Macronix PCI ethernet adatper, and I am using driver "io-net -d
tulip -p tcpip".

Can anyone help me please?




Chris McKillop

Re: QNX 6.2.1 NC ethernet card problem

Post by Chris McKillop » Sat Aug 02, 2003 5:12 am

xinni <xiahnisong2001@rogers.com> wrote:
I installed 6.2.1NC, but I cannot have the ethernet card running: when I
configure the en0 to use DHCP, I got an pop-up message "netmanager
error:could not configure DHCP on interface en0. netmanager error: couldnot
reach DHCP server on interface en0."

I have a Macronix PCI ethernet adatper, and I am using driver "io-net -d
tulip -p tcpip".

Can anyone help me please?
Care to post the output from nicinfo once you have started io-net?

chris

--
Chris McKillop <cdm@qnx.com> "The faster I go, the behinder I get."
Software Engineer, QSSL -- Lewis Carroll --
http://qnx.wox.org/

xinni

Re: QNX 6.2.1 NC ethernet card problem

Post by xinni » Tue Aug 05, 2003 12:22 am

Hi,
Here's the output from nicinfo:

Tulip: Macronix 98715 Ethernet Controller
Physical Node
ID.................................................................0080C6
E544AB
Current Physical Node
ID....................................................0080C6 E544AB
Media
Rate........................................................................
...100.00 Mb/s half-duplex UTP

MTU.........................................................................
............1514

Lan.........................................................................
...............0
I/O Port
Range......................................................................0
x7000 - >0x70FF
Hardware
Interrupt................................................................0xA

Promiscuous.................................................................
..........Disabled

Multicast...................................................................
.............Enabled

Total Packets Txd
OK........................................................18
Total Packets Txd
Bad........................................................0
Total Packets Rxd
OK........................................................1284
Total Packets Rxd
Bad........................................................0

Total Bytes
Txd...................................................................3762
Total Bytes
Rxd...................................................................82474

Tx Collision
Errors...............................................................0
Tx Collision
Errors(aborted).................................................0
Carrier Sense lost on
Tx.......................................................0
FIFO underruns during
Tx....................................................0
Tx
deferred....................................................................
.......0
Out of window
collision........................................................0
FIFO underruns during
Rx....................................................0
Allignment
Errors.................................................................0
CRC
Errors......................................................................
.....0


Thanks!


"Chris McKillop" <cdm@qnx.com> wrote in message
news:bgfh8a$ekn$1@nntp.qnx.com...
xinni <xiahnisong2001@rogers.com> wrote:
I installed 6.2.1NC, but I cannot have the ethernet card running: when I
configure the en0 to use DHCP, I got an pop-up message "netmanager
error:could not configure DHCP on interface en0. netmanager error:
couldnot
reach DHCP server on interface en0."

I have a Macronix PCI ethernet adatper, and I am using driver "io-net -d
tulip -p tcpip".

Can anyone help me please?


Care to post the output from nicinfo once you have started io-net?

chris

--
Chris McKillop <cdm@qnx.com> "The faster I go, the behinder I get."
Software Engineer, QSSL -- Lewis Carroll --
http://qnx.wox.org/

Post Reply

Return to “qdn.public.installation”