I´m user QNX 6.2. I need more LPT ports than one. I have chosen PCI card
from
Kouwell (220N-2 with chipset Nm9715cv), which has 2 additional LPT ports,
but I don´t know how to install or set this card.
If I enter command : pci -vvv , I get output:
.....
.....
.....
Class = Communication (Unknown)
Vendor ID = 9710h, Netmos
Device ID = 9815h, Nm9815 Parallel Port Adapter
PCI index = 0h
Class Codes = 078000h
Revision ID = 1h
Bus number = 0
Device number = 15
Function num = 0
Status Reg = 280h
Command Reg = 103h
I/O space access enabled
Memory space access enabled
Bus Master disabled
Special Cycle operations ignored
Memory Write and Invalidate disabled
Palette Snooping disabled
Parity Checking disabled
Data/Address stepping disabled
SERR# driver disabled
Fast back-to-back transactions to different agents enabled
Header type = 0h Single-function
BIST = 0h Build-in-self-test not supported
Latency Timer = c0h
Cache Line Size= 8h un-cacheable
PCI IO Address = dc00h length 8 enabled
PCI IO Address = d800h length 8 enabled
PCI IO Address = d400h length 8 enabled
PCI IO Address = d000h length 8 enabled
PCI IO Address = cc00h length 8 enabled
PCI IO Address = c800h length 16 enabled
Subsystem Vendor ID = 1000h
Subsystem ID = 20h
Max Lat = 0ns
Min Gnt = 0ns
PCI Int Pin = INT A
Interrupt line = 10
Device Dependent Registers:
0x40: 80 80 00 00 00 00 00 00 00 00 00 00 00 00 00 00
0x50: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
0x60: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
0x70: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
0x80: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
0x90: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
0xA0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
0xB0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
0xC0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
0xD0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
0xE0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
0xF0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
.....
.....
.....
PCI card with 2 LPT
bridged with qdn.public.ddk.printer
Post Reply
1 post
• Page 1 of 1
Return to “qdn.public.ddk.printer”
Jump to
- New qnx.* Newsgroup
- ↳ qnx.newuser
- ↳ qnx.rtos
- ↳ qnx.gui
- ↳ qnx.development_tools
- ↳ qnx.ddk
- ↳ qnx.porting
- ↳ qnx.bsp
- ↳ qnx.qnx4
- ↳ qnx.3rdparty_product_announcements
- ↳ qnx.cafe
- ↳ qnx.public.sysadmin
- ↳ qnx.evaluation
- QDN Newsgroups
- ↳ qdn.cafe
- ↳ qdn.public.qnx2
- ↳ qdn.public.qnx4
- ↳ qdn.public.neutrino
- ↳ qdn.public.photon
- ↳ qdn.public.porting
- ↳ qdn.public.news
- ↳ qdn.public.qnxjobs
- ↳ qdn.public.qnxrtp.newuser
- ↳ qdn.public.qnxrtp.installation
- ↳ qdn.public.qnxrtp.os
- ↳ qdn.public.qnxrtp.photon
- ↳ qdn.public.qnxrtp.devtools
- ↳ qdn.public.qnxrtp.applications
- ↳ qdn.public.qnxrtp.advocacy
- ↳ qdn.public.qnx4.photon
- ↳ qdn.public.qnx4.devtools
- ↳ qdn.public.articles
- ↳ qdn.public.ddk.graphics
- ↳ qdn.public.ddk.network
- ↳ qdn.public.ddk.audio
- ↳ qdn.public.ddk.input
- ↳ qdn.public.ddk.usb
- ↳ qdn.public.ddk.printer
- ↳ qdn.public.qnxrtp.porting
- ↳ qdn.public.qnxrtp.games
- ↳ qdn.public.qnxrtp.embedded
- ↳ qdn.public.qnxrtp.mips
- ↳ qdn.public.qnxrtp.powerpc
- ↳ qdn.public.qnxrtp.strongarm
- ↳ qdn.public.qnxrtp.x86
- ↳ qdn.public.sysadmin
- ↳ qdn.public.qnxrtp.xscale
- ↳ qdn.public.qnxrtp.sh4
- ↳ qdn.public.newuser
- ↳ qdn.public.installation
- ↳ qdn.public.devtools
- ↳ qdn.public.ddk
- ↳ qdn.public.bsp
- Other QNX Newsgroups
- ↳ comp.os.qnx
- ↳ openqnx.developer